Komatsu PC200-6, PC200LC-6, PC210LC-6, PC220LC-6, PC250LC-6 (SN A83000-) excavator pdf operation and maintenance manual

Table of Contents for KOMATSU-CEAD001200-OM-EN manual

• MAIN MENU
• COVER
• 1. FORWARD
• 2. SAFETY INFORMATION
• 3. INTRODUCTION
  • 3.1 INTENDED USE
  • 3.2 FEATURES
  • 3.3 BREAKING IN A NEW MACHINE
• 4. LOCATION OF PLATES, TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
  • 4.1 MACHINE SERIAL NO. PLATE POSITION
  • 4.2 ENGINE SERIAL NO. PLATE POSITION
  • 4.3 TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
• 5. CONTENTS
• 6. GENERAL PRECAUTIONS
• 7. PRECAUTIONS DURING OPERATIONS
  • 7.1 BEFORE STARTING ENGINE
  • 7.2 OPERATING MACHINE
  • 7.3 TRANSPORTATION
  • 7.4 BATTERY
  • 7.5 TOWING
  • 7.6 BUCKET WITH HOOK
• 8. PRECAUTIONS FOR MAINTENANCE
  • 8.1 BEFORE CARRYING OUT MAINTENANCE
  • 8.2 DURING MAINTENANCE
• 9. POSITION FOR ATTACHING SAFETY LABELS
• 10. GENERAL VIEW
  • 10.1 GENERAL VIEW OF MACHINE
  • 10.2 GENERAL VIEW OF CONTROLS AND GAUGES
• 11. EXPLANATION OF COMPONENTS
  • 11.1 MACHINE MONITOR
  • 11.2 SWITCHES
  • 11.3 CONTROL LEVERS, PEDALS
  • 11.4 CEILING WINDOW
  • 11.5 FRONT WINDOW
  • 11.6 DOOR LOCK
  • 11.7 CAP, COVER WITH LOCK
  • 11.8 HOT/COOL BOX
  • 11.9 LUGGAGE BOX
  • 11.10 ASHTRAY
  • 11.11 CAB HEATER
  • 11.12 CAR RADIO
  • 11.13 FUSE
  • 11.14 FUSIBLE LINK
  • 11.15 CONTROLLER
  • 11.16 TOOL BOX
  • 11.17 GREASE PUMP HOLDER
  • 11.18 HANDLING ACCUMULATOR
• 12. OPERATION
  • 12.1 CHECK BEFORE STARTING ENGINE
  • 12.2 STARTING ENGINE
  • 12.3 OPERATIONS AND CHECKS AFTER STARTING ENGINE
  • 12.4 MOVING MACHINE
  • 12.5 STEERING MACHINE
  • 12.6 STOPPING MACHINE
  • 12.7 SWINGING
  • 12.8 OPERATION OF WORK EQUIPMENT
  • 12.9 HANDLING ACTIVE MODE
  • 12.10 WORKING MODE SELECTION
  • 12.11 PROHIBITIONS FOR OPERATION
  • 12.12 PRECAUTIONS FOR OPERATION
  • 12.13 PRECAUTIONS WHEN TRAVELING UP OR DOWN HILLS
  • 12.14 HOW TO ESCAPE FROM MUD
  • 12.15 WORK POSSIBLE USING HYDRAULIC EXCAVATOR
  • 12.16 REPLACEMENT AND INVERSION OF BUCKET
  • 12.17 PARKING MACHINE
  • 12.18 CHECK AFTER FINISHING WORK
  • 12.19 STOPPING ENGINE
  • 12.20 CHECK AFTER STOPPING ENGINE
  • 12.21 LOCKING AND SECURING MACHINE
• 13. TRANSPORTATION
  • 13.1 LOADING, UNLOADING WORK
  • 13.2 PRECAUTIONS FOR LOADING
  • 13.3 PRECAUTIONS FOR TRANSPORTATION
• 14. COLD WEATHER OPERATION
  • 14.1 PRECAUTIONS FOR LOW TEMPERATURE
  • 14.2 PRECAUTIONS AFTER COMPLETION OF WORK
  • 14.3 AFTER COLD WEATHER
• 15. LONG-TERM STORAGE
  • 15.1 BEFORE STORAGE
  • 15.2 DURING STORAGE
  • 15.3 AFTER STORAGE
  • 15.4 STARTING MACHINE AFTER LONG-TERM STORAGE
• 16. TROUBLESHOOTING
  • 16.1 PHENOMENA THAT ARE NOT FAILURES
  • 16.2 METHOD OF TOWING MACHINE
  • 16.3 METHOD FOR USING LIGHT-WEIGHT TOWING HOLE
  • 16.4 PRECAUTIONS ON PARTICULAR JOBSITES
  • 16.5 IF BATTERY IS DISCHARGED
  • 16.6 OTHER TROUBLE
• 17. GUIDES TO MAINTENANCE
• 18. OUTLINES OF SERVICE
  • 18.1 OUTLINE OF OIL, FUEL, COOLANT
  • 18.2 OUTLINE OF ELECTRICAL SYSTEM
  • 18.3 OUTLINE OF HYDRAULIC SYSTEM
• 19. WEAR PARTS LIST
• 20. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
  • 20.1 ENGINE OIL SPECIFICATION
  • 20.2 DIESEL FUEL SPECIFICATIONS
• 21. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
  • 21.1 INTRODUCTION OF NECESSARY TOOLS
  • 21.2 TORQUE LIST
• 22. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
• 23. MAINTENANCE SCHEDULE CHART
  • 23.1 MAINTENANCE SCHEDULE CHART
  • 23.2 MAINTENANCE INTERVAL WHEN USING HYDRAULIC BREAKER
• 24. SERVICE PROCEDURE
  • 24.1 INITIAL 250 HOURS SERVICE
  • 24.2 WHEN REQUIRED
  • 24.3 CHECK BEFORE STARTING
  • 24.4 EVERY 100 HOURS SERVICE
  • 24.5 EVERY 250 HOURS SERVICE
  • 24.6 EVERY 500 HOURS SERVICE
  • 24.7 EVERY 1000 HOURS SERVICE
  • 24.8 EVERY 2000 HOURS SERVICE
  • 24.9 EVERY 4000 HOURS SERVICE
  • 24.10 EVERY 5000 HOURS SERVICE
• 25. SPECIFICATIONS
• 26. GENERAL PRECAUTIONS
  • 26.1 PRECAUTIONS RELATED TO SAFETY
  • 26.2 PRECAUTIONS WHEN INSTALLING ATTACHMENTS
• 27. HANDLING BUCKET WITH HOOK
  • 27.1 CHECK FOR DAMAGE TO BUCKET WITH HOOK
  • 27.2 PROHIBITED OPERATIONS
  • 27.3 PRECAUTIONS DURING OPERATIONS
• 28. HANDLING AIR CONDITIONER
  • 28.1 GENERAL LOCATIONS ON CONTROL PANEL
  • 28.2 PRECAUTIONS WHEN USING AIR CONDITIONER
• 29. MACHINES READY FOR ATTACHMENTS
  • 29.1 EXPLANATION OF COMPONENTS
  • 29.2 HYDRAULIC CIRCUIT
  • 29.3 ATTACHMENT MOUNTING/DISMOUNTING PROCEDURE
  • 29.4 OPERATION
  • 29.5 LONG-TERM STORAGE
  • 29.6 SPECIFICATIONS
• 30. INTRODUCTION OF ATTACHMENTS
  • 30.1 BUCKET SELECTION
  • 30.2 BUCKET INSTALLATION COMBINATIONS
  • 30.3 SELECTION OF TRACK SHOES
  • 30.4 BACKHOE CONTROL PATTERN CONVERSION
• 31. EXTENDING MACHINE SERVICE LIFE
  • 31.1 HYDRAULIC BREAKER
  • 31.2 CRUSHER
  • 31.3 GRAPPLE
  • 31.4 BUCKET WITH THUMB GRAPPLE
  • 31.5 ROTATING GRAPPLE
  • 31.6 SHEAR
  • 31.7 HYDRAULIC PILE DRIVER