Massey Ferguson 4608 / 4609 / 4610 tractor service manual

Table of Contents for MF-4283492M3 manual

• 4600 Series Tractors Service Manual
• Table of contents
• 1. Introduction
  • 1.1 Introduction
  • 1.2 Specifications
  • 1.3 General dimensions
  • 1.4 Lubrication / fill points
  • 1.5 General precautions for disassembly and installation
  • 1.6 Tightening torque chart
  • 1.7 Conversion table
• 2. Safety
  • 2.1 Introduction
  • 2.2 Operation
  • 2.3 Travel on public roads
  • 2.4 Maintenance
• 3. Engine
  • 3.1 Component access
  • 3.2 Radiator
  • 3.3 Removing the engine
  • 3.4 Installing the engine
  • 3.5 Fuel tank
  • 3.6 Electronic diagnostic tool
  • 3.7 Engine service manual
• 4. Power train
  • 4.1 Separating the engine from the front transmission
  • 4.2 Separating the front and mid-transmission housings
  • 4.3 Separating the mid and rear transmission housings
  • 4.4 Separating the rear axle from the rear transmission case
  • 4.5 Attaching the rear axle to the rear transmission case
  • 4.6 Power shuttle transmission
  • 4.7 Power train
  • 4.8 Gear ratios
  • 4.9 Shuttle clutch
  • 4.10 Clutch pack
  • 4.11 Input gears
  • 4.12 Transmission main change gears
  • 4.13 Creeper gear
  • 4.14 Transmission range change gears
• 5. Cab and platform
  • 5.1 Platform
  • 5.2 Cab
  • 5.3 Seat
  • 5.4 Roll over protective structure
  • 5.5 Steering column
  • 5.6 Steering wheel
  • 5.7 Mirrors
  • 5.8 Air conditioning system
  • 5.9 Troubleshooting the air conditioner system
• 6. Frame and axles
  • 6.1 Hydrostatic steering
  • 6.2 Fender
  • 6.3 Engine cover
  • 6.4 Three-point linkage and drawbar
  • 6.5 Rear axle
  • 6.6 Rear axle housing and differential gears
  • 6.7 Ring gear and pinion
  • 6.8 Brakes
  • 6.9 Differential
  • 6.10 Front axle
  • 6.11 Front differential (four-wheel drive only)
  • 6.12 Final drive housing (four-wheel drive only)
  • 6.13 Front wheel alignment
  • 6.14 Front axle troubleshooting
• 7. Electrical
  • 7.1 Wire color chart
  • 7.2 Power shuttle general information
  • 7.3 Wiring diagrams
  • 7.4 Instruments and controls
  • 7.5 Valves
  • 7.6 Position of the main electrical parts
  • 7.7 Sensor initial adjustment
  • 7.8 Electrical and hydraulic control system
  • 7.9 Main clutch system
  • 7.10 Electronic diagnostic tool
  • 7.11 Fault code tree
  • 7.12 Diagnostic codes
• 8. Hydraulics
  • 8.1 Hydraulic schematic
  • 8.2 Specifications
  • 8.3 Transmission oil cooler and lubrication
  • 8.4 General service procedures
  • 8.5 Suction filter
  • 8.6 Gear pump
  • 8.7 Cylinders
  • 8.8 Valves
  • 8.9 Parts and hydraulic diagrams
  • 8.10 Hydraulic system troubleshooting
• Index
• 4600 Engine fault code troubleshooting.pdf
  • Introduction
  • EEM4 general instructions
  • Fault Codes
  • Sensor details
  • Aftertreatment
  • Engine electric system
  • ECU Replacement Procedure
  • Sisu fault codes.pdf
  • Blank Page