Massey Ferguson WR9950, WR9960, WR9970, WR9980 self-propelled windrower pdf service manual

Table of Contents for MF-4283616M2 manual

• Windrower WR9950 - WR9980 WSM
• TABLE OF CONTENT
• 1. General
  • 1.1 General information
  • 1.2 Safety
  • 1.3 Machine identification
  • 1.4 Specifications
  • 1.5 Service schedule
  • 1.6 Bolt torque values
  • 1.7 Active and recent fault codes
  • 1.8 Machine fault codes
  • 1.9 Fault code diagnostic trees for the AGCO Power engine
  • 1.10 HVAC fault codes
  • 1.11 AG3000 EDT fault code
  • 1.12 Machine main components
  • 1.13 Component access
  • 1.14 Calibrations
• 2. Engine, Fuel And Exhaust System
  • 2.1 Engine oil
  • 2.2 Belts
  • 2.3 Engine air filter
  • 2.4 Pump drive gearbox
  • 2.5 Cooling system
  • 2.6 Fuel system
  • 2.7 Selective catalytic reduction (SCR) system, if equipped
  • 2.8 Safety instructions
  • 2.9 To the user
  • 2.10 Engine construction
  • 2.11 Technical data
  • 2.12 Tightening torques
  • 2.13 Special tools
  • 2.14 Liquid quality requirements
  • 2.15 Major maintenance and engine replacement
  • 2.16 Cylinder block
  • 2.17 Flywheel housing
  • 2.18 Cylinder head
  • 2.19 Valve mechanism
  • 2.20 Crankshaft
  • 2.21 Connecting rods and pistons
  • 2.22 Counterbalance in 4 cylinder engines
  • 2.23 Flywheel
  • 2.24 Timing gear assembly
  • 2.25 Lubrication system
  • 2.26 Cooling system
  • 2.27 Air control system maintenance
  • 2.28 Fuel system
  • 2.29 SCR system
  • 2.30 Engine control system
• 3. Steering System
  • 3.1 Ground drive
  • 3.2 Steering column
• 4. Drive Train System
  • 4.1 Final drives
• 5. Hydraulic System
  • 5.1 Hydraulic oil level
  • 5.2 Principle of operation of a hydraulic motor and pump
  • 5.3 Hydraulic circuits
  • 5.4 Hydraulic oil filters
  • 5.5 Hydraulic troubleshooting and testing
  • 5.6 Clean and flush the hydraulic system
  • 5.7 Header drive pump and Propel drive pump
  • 5.8 Gear pump
  • 5.9 Wheel motors
  • 5.10 Fan motor
  • 5.11 Auxiliary function valve
  • 5.12 Header down valve
  • 5.13 Bypass valve
  • 5.14 Rear steer valve, if equipped
  • 5.15 Header lift cylinder
  • 5.16 Header flotation cylinders
  • 5.17 Header tilt cylinder
  • 5.18 Rear steer cylinders, if equipped
  • 5.19 Cylinder repair
  • 5.20 Accumulator
  • 5.21 Hydraulic oil tank
• 6. Electrical System
  • 6.1 Basic troubleshooting information
  • 6.2 Connectors
  • 6.3 Bulb replacement
  • 6.4 Fuses and relays
  • 6.5 Troubleshooting the charging circuit
  • 6.6 Alternator
  • 6.7 Starter
  • 6.8 Start engine with a booster battery
  • 6.9 Controllers
  • 6.10 Solenoid valves
  • 6.11 Diagnostics on the terminal
  • 6.12 Software version
  • 6.13 Tractor to header connector
• 7. Cab
  • 7.1 Suspended cab
  • 7.2 Cab roof
  • 7.3 Windscreen
• 8. Air Conditioning And Heating System
  • 8.1 Cab air filter
  • 8.2 Air conditioning and heating system
  • 8.3 Test and adjust
  • 8.4 Basic air conditioning system testing
  • 8.5 System pressure check
  • 8.6 Manifold gauge set readings
  • 8.7 Refrigerant recovery
  • 8.8 Climate control system
  • 8.9 Compressor
  • 8.10 Compressor clutch
  • 8.11 Condenser
  • 8.12 Receiver dryer
• 9. Chassis
  • 9.1 Engine cover
  • 9.2 Header lift
  • 9.3 Level the header
• 10. Spindles and wheels
  • 10.1 Wheels and tires
  • 10.2 Adjust the rear axle tread width
  • 10.3 Dampner
  • 10.4 Spindles - without rear steer
  • 10.5 Spindles - with rear steer
  • 10.6 Wheel bearings
  • 10.7 Suspended rear axle
  • 10.8 Rigid rear axle
• 11. Diagrams
  • 11.1 Hydraulics
  • 11.2 How to read wiring schematics
  • 11.3 Electrical tables
  • 11.4 Electrical wiring diagrams
  • 11.5 Connector location
• Index