Massey Ferguson 630, 650, 660, 680 tractor pdf workshop service manual

Table of Contents for MF-600-03-WSM-EN manual

• CONTENTS
• Introduction
  • 1 - Introduction
  • 2 - Safety
  • 3 - Correct workshop techniques
  • 4 - Basics of measurement
  • 5 - General table of recommended torques for bolts
  • 6 - Technical units
  • 7 - Loctite products for the workshop
  • 8 - AGCO's environmental policy
  • 9 - Compulsory recycling of batteries
• Splitting the tractor
  • 1 - Introduction
  • 2 - Splitting the tractor between engine and front axle
  • 3 - Splitting the tractor between the engine and gearbox
  • 4 - Splitting the tractor between gearbox and rear axle
  • 5 - Splitting the tractor rearwards between gearbox and rear
  • 6 - Front hood sheet metal removal
• 4WD Front Axles Carraro 20.201 and 10.29
  • 1 - Introduction
  • 2 - Final drives
  • 3 - Final drive pivoting
  • 4 - Half-shaft spiders
  • 5 - Bushings and retainers of trumpets and pivots
  • 6 - Pinion and differential assy
  • 7 - Driving box and front bearing shell
  • 8 - Steering cylinder
  • 9 - General table of tightening torques
• 4WD Front Axles ZF / APL 350 and 359
  • 1 - Introduction
  • 2 - Final drives
  • 3 - Differential, pinion and trumpets
  • 4 - Secondary driving box, brackets and bearings
  • 5 - Four-wheel drive front axle driving box and spacer
  • 6 - Steering unit hydraulic cylinder
  • 7 - Adjustment specifications
• Perkins Engines
  • 1 - Adjustment of valve tip clearance
  • 2 - Inspection of nozzles
  • 3 - Adjustment of the injection point
  • 4 - Compression test for cylinders
  • 5 - Basic technical specifications
  • 6 - Workshop specifications
• Clutch
  • 1 - Clutches fitted on the Advanced 600 series tractors
  • 2 - Clutches and flywheels fitted on the 600 series tractors
  • 3 - General information and recommendations on clutches
  • 4 - Dual-stage and split-torque clutch: component identification
  • 5 - Clutch removal and disassembly
  • 6 - Inspection and refitting of components
  • 7 - Clutch reassembly (dual-stage and split-torque)
  • 8 - Engine flywheel
  • 9 - Clutch refitting and final adjustments
  • 10 - Clutch troubleshooting
  • Double disc clutch
• Eaton Constant Mesh 12x4-speed Gearbox
  • 1 - Introduction
  • 2 - Gearbox removal and adaptation to service support
  • 3 - Shift lever shafts and forks
  • 4 - Clutch release mechanism
  • 5 - Slow/Fast range assy
  • 6 - Front flange (input housing) and input shafts
  • 7 - Main shaft (or output shaft)
  • 8 - PTO output shaft and layshaft (lower)
  • 9 - Reverse gear assy
  • 10 - Component inspection and failure diagnosis (troubleshooting)
  • 11 - Recommendations on bushings and sleeves
  • 12 - Coupler assemblies
• Eaton Synchromesh 12x4-speed
  • 1 - Introduction
  • 2 - Gearbox removal and adaptation to service support
  • 3 - Clutch release mechanism
  • 4 - Slow/Fast range assy
  • 5 - Front flange (input housing) and input shafts
  • 6 - Main shaft (or output shaft)
  • 7 - PTO output shaft and layshaft (lower)
  • 8 - Reverse gear assy
  • 9 - Synchronizer assemblies
  • 10 - Component inspection and failure diagnosis (troubleshooting)
• 12x5-speed gearbox - ZF T 3500
  • 1 - Introduction
  • 2 - Gearbox removal from tractor
  • 3 - Levers, upper cover and gear shift lever shafts
  • 4 - T3500 gearbox lubricating system
  • 5 - Hydraulic pump driving box
  • 6 - Clutch engagement mechanism
  • 7 - 4WD drop box
  • 8 - Gearbox inner assy removal and disassembly
  • 9 - Inspection of components
  • 10 - Gearbox troubleshooting
  • 11 - Reassembly and adjustments
• Rear Axle
  • 1 - Description and operation
  • 2 - Final drives
  • 3 - Trumpets
  • 4 - Brakes
  • 5 - Differential
  • 6 - Pinion
  • 7 - Adjustments and reinstallation of the ring gear and pinion assembly
  • 8 - Table of general technical specifications
• Ferguson Hydraulic Lift System
  • 1 - Introduction
  • 2 - Ferguson hydraulic linkage system operation
  • 3 - Ferguson hydraulic linkage pump
  • 4 - Hydraulic lift cover
  • 5 - Outer hydraulic cylinders
• Hydrotronic Hydraulic Lift System
  • 1 - Identification of operation and components
  • 2 - Identification of panel components
  • 3 - Circuits and diagrams
  • 4 - Raise/Lower control valve
  • 5 - Hydraulic cylinders
  • 6 - Refitting and adjustment of sensors
  • 7 - Hydraulic lift cover
  • 8 - Maintenance of the electro-electronic components
  • 9 - Troubleshooting tests
  • 10 - Technical specifications
• Boschtronic Hydraulic Lift System
  • 1 - Identification of operation and components
  • 2 - Identification of panel components
  • 3 - Circuits and diagrams
  • 4 - Lift control valve
  • 5 - Refitting and adjustment of sensors
  • 6 - Maintenance of the electro-electronic components
  • 7 - Troubleshooting tests
  • 8 - Technical specifications
• Power take-off
  • 1 - Introduction
  • 2 - Removing the IPTO assembly
  • 3 - IPTO side cover and control valve assy
  • 4 - Clutch disc pack assy
  • 5 - IPTO drive pump
  • 6 - Dual rotation PTO / IPTO - 1000 / 540 RPM
  • 7 - Refitting the IPTO assy into the tractor
  • 8 - Live Power Take-off
• Electrical System
  • 1 - Introduction
  • 2 - Electrical board: fuses, relays, and diodes
  • 3 - Prestolite alternator
  • 4 - Prestolite starter motor
  • 5 - Instrument panel
  • 6 - Miscellaneous components
• Auxiliary Hydraulic Systems
  • 1 - Introduction
  • 2 - Hydraulic testing
  • 3 - Danfoss hydrostatic steering unit
  • 4 - Danfoss priority valve
  • 5 - Auxiliary hydraulic control valve
  • 6 - Hydraulic pump(s)
  • 7 - Oil filtering
  • 8 - Heat exchanger
• Cab, Air Conditioning System and Heating
  • 1 - Introduction
  • 2 - Operation
  • 3 - Technical features
  • 4 - Safety recommendations
  • 5 - General maintenance
  • 6 - Preventive maintenance control
  • 7 - Electrical diagram
  • 8 - Coolant refilling
  • 9 -Troubleshooting
  • 10 - Windshield wiper (front)
  • 11 - Fan and heating system
• Technical Specifications MF 630, 650, 660 and 680
  • 1 - Engine
  • 2 - Electrical system - powers and capacities
  • 3 - Clutch
  • 4 - Gearbox
  • 5 - Rear Axle
  • 6 - 4WD front axle
  • 7 - Brakes
  • 8 - Hydraulic lift system
  • 9 - Auxiliary hydraulic systems
  • 10 - Power Take-off
  • 11 - Tractors' weights - in Kgf
  • 12 - Tractors' general dimensions - in mm
  • 13 - Filling capacity - in liters
  • 14 - Tightening torque for wheel nuts and bolts - kgf.m
  • 15 - Drawbar
  • 16 - Cab and air conditioning system (optional for MF 650, 660 and 680)