Massey Ferguson 2240, 2250, 2260, 2270, 2270XD, 2290 baler pdf operator's manual

Table of Contents for MF-700741468F-EN manual

• 700741468F-OIB-00-EN
• TABLE OF CONTENT
• 1. Safety
  • 1.1 Introduction
  • 1.2 Operation
  • 1.3 Travel on public roads
  • 1.4 Maintenance
  • 1.5 Safety and information signs
• 2. Introduction
  • 2.1 Introduction
  • 2.2 Machine identification
  • 2.3 Machine components
  • 2.4 Knotters
• 3. Operation
  • 3.1 Checklists
  • 3.2 High quality hay
  • 3.3 Brakes and locks
  • 3.4 Connect to the tractor
  • 3.5 Electrical, hydraulic, and brake connections
  • 3.6 Baler operation
  • 3.7 Electronics
  • 3.8 Pickup and windguard
  • 3.9 Knotter and needles
  • 3.10 Change the bale length
  • 3.11 Rotor cutter - early production cutter
  • 3.12 ProCut™ rotary cutter
  • 3.13 Packer/Cutter
  • 3.14 Roller bale chute, if equipped
  • 3.15 Lighting and reflectors
  • 3.16 Tandem axle steering lock
  • 3.17 Preparing to road the machine or to move the machine on a trailer
  • 3.18 Lift and tie down the machine
  • 3.19 Thread a four twine machine
  • 3.20 Thread a six twine machine
  • 3.21 Remove a bale from the bale chamber
  • 3.22 Air brake pressure release
  • 3.23 Disconnect the tractor
• 4. Maintenance
  • 4.1 Service schedule
  • 4.2 General maintenance information
  • 4.3 Lubrication points
  • 4.4 Main Gearbox
  • 4.5 Rotor cutter gearbox, if equipped
  • 4.6 Hydraulic system
  • 4.7 Shearbolts
  • 4.8 Knotter lubrication pump
  • 4.9 Chain lubrication pump, if equipped
  • 4.10 Flywheel brake
  • 4.11 Slip clutches
  • 4.12 Drive chains
  • 4.13 Time the machine
  • 4.14 Rotor cutter - early production cutter
  • 4.15 ProCut™ rotary cutter
  • 4.16 Stuffer
  • 4.17 Plunger
  • 4.18 Knotter system maintenance
  • 4.19 Needle maintenance
  • 4.20 Adjust the needle protection linkage
  • 4.21 Sensors and switches locations and specifications
  • 4.22 Tires, wheels, and axles
  • 4.23 Brakes
  • 4.24 Prepare for storage
  • 4.25 Prepare for a new season
• 5. Troubleshooting
  • 5.1 Shearbolt troubleshooting
  • 5.2 Main drive train troubleshooting
  • 5.3 Main gearbox troubleshooting
  • 5.4 Feed system troubleshooting
  • 5.5 Stuffer troubleshooting
  • 5.6 Knotter/needle clutch troubleshooting
  • 5.7 Tying troubleshooting
  • 5.8 Needle troubleshooting
  • 5.9 Bale length troubleshooting
  • 5.10 Bale shape troubleshooting
  • 5.11 Knotter blower troubleshooting, if equipped
  • 5.12 Knotter lubrication system troubleshooting
  • 5.13 Hydraulic troubleshooting
  • 5.14 Alarm troubleshooting
  • 5.15 Ejector troubleshooting, if equipped
  • 5.16 Brake troubleshooting, if equipped
  • 5.17 Electronic troubleshooting
• 6. Specification
  • 6.1 Specifications
• 7. Accessories
  • 7.1 Accessories
• 8. Assembly
  • 8.1 Assemble the machine
  • 8.2 Checklists
• Index