Massey Ferguson DELTA 9280 combine harvester workshop manual

Table of Contents for MF-D3112800M1 manual

• Workshop Manual
• Contents
• 0. Introduction - Specifications
  • 0.1 Using the manual
  • 0.2 General specifications
  • 0.3 Dimensions and weight
  • 0.4 Safety precautions
  • 0.5 Practical advice
  • 0.6 Start-up instructions
  • 0.7 Conversion tables
  • 0.8 Locking and sealing agents
  • 0.9 Wheel nut torques
• 1. Cutting table
  • 1.1 General
  • 1.2 Knife drive - wobble box
  • 1.3 Table auger
  • 1.4 Table body
  • 1.5 Slip clutch and chain drive
  • 1.6 Countershaft
  • 1.7 PowerFlow table
• 2. Reel
  • 2.1 Reel
  • 2.2 Oil motor and chain drive
  • 2.3 Hydraulic cylinders
• 3. Main crop elevator
  • 3.1 General
  • 3.2 Main crop elevator
  • 3.3 Crop elevator chain
  • 3.4 Elevator chain top shaft
  • 3.5 Elevator chain front shaft
  • 3.6 Elevator countershaft
  • 3.7 Table clutch and chain drive
  • 3.8 Adapter
  • 3.9 Hydraulic reversing
• 4. Threshing unit
  • 4.1 General
  • 4.2 Stone trap
  • 4.3 Concave
  • 4.4 Threshing cylinder
  • 4.5 Cylinder variator – table clutch
  • 4.6 Bracket for counter drive
  • 4.7 Rear beater
  • 4.8 Rear beater concave
  • 4.9 Rotor Feeder
  • 4.10 Rotor Feeder concave
• 5. Rotor unit
  • 5.1 General
  • 5.2 Rotor variator
  • 5.3 Shaft for mechanical variator
  • 5.4 Right-angle gear
  • 5.5 Rotor
  • 5.6 Rotor cage
• 6. Shaker shoe - Fanning mill
  • 6.1 General
  • 6.2 Fanning Mill
  • 6.3 Main grain pan frame
  • 6.4 Second grain pan
  • 6.5 Top shaker shoe
  • 6.6 Bottom shaker shoe
  • 6.7 Bottom augers
  • 6.8 Eccentric drive
  • 6.9 Transmissions
• 7. Elevators
  • 7.1 Tank filling elevator
  • 7.2 Returns elevator
  • 7.3 Returns thresher
  • 7.4 Tank filling auger
  • 7.5 Transmission
• 8. Engine
  • 8.1 General
  • 8.2 Replacing the engine
• 9. Unloading auger - Grain tank
  • 9.1 Unloading auger - horizontal
  • 9.2 Unloading auger - vertical
  • 9.3 Unloading tube - horizontal
  • 9.4 Unloading tube - vertical
  • 9.5 Unloading tube elbow
  • 9.6 Bottom auger and cover plate
  • 9.7 Transmission
  • 9.8 Grain tank covers
• 10. Drive unit
  • 10.1 Radiator - Intercooler
  • 10.2 Oil cooler
  • 10.3 Condenser – air conditioning
  • 10.4 Rotary screen
  • 10.5 Dust aspirator
  • 10.6 Hydrostatic pump
  • 10.7 Auxiliary hydraulic pump
  • 10.8 Hydraulic pump - Maxi Spreader
  • 10.9 Hydraulic oil tank
  • 10.10 Fuel tank
  • 10.11 AdBlue tank
  • 10.12 Compressor – air conditioning
  • 10.13 Power take-off
• 11. Transmissions
  • 11.1 General
  • 11.2 Countershaft
  • 11.3 Replacing the belts, right- hand side
  • 11.4 Replacing the chains, right- hand side
  • 11.5 Replacing the belts, left-hand side
  • 11.6 Replacing the chains, left- hand side
• 12. Undercarriage
  • 12.1 Auto Level final drive bracket
  • 12.2 Final drives
  • 12.3 Gearbox
  • 12.4 Hydrostatic motor
  • 12.5 Brakes
  • 12.6 Rear axle
• 13. Cab
  • 13.1 Multi-function lever and control panel
  • 13.2 Replacing the windscreen
  • 13.3 Control panel in roof
  • 13.4 Roof
  • 13.5 Troubleshooting – Climate control
• 14. Hydraulics
  • 14.1 General
  • 14.2 Hydrostatic system
  • 14.3 Gearshift
  • 14.4 Hand brake
  • 14.5 Auxiliary hydraulics
  • 14.6 Cutting table
  • 14.7 Auto Level
  • 14.8 Reel
  • 14.9 Steering
  • 14.10 Cylinder variator
  • 14.11 Rotor variator
  • 14.12 Unloading auger
  • 14.13 Reversing
  • 14.14 Chaff spreader
  • 14.15 Maxi Spreader
  • 14.16 Troubleshooting - hydrostatic transmission
• 15. Electrical system
  • 15.1 General
  • 15.2 Description of DATAVISION.
  • 15.3 Electric box
  • 15.4 Calibrations
  • 15.5 Diagrams overview
  • 15.6 Wiring diagrams
  • 15.7 Diagrams - computer input/output
  • 15.8 Connectors
  • 15.9 W-connecting points
  • 15.10 Components
  • 15.11 Key to symbols
  • 15.12 Wiring overview
• 16. Straw chopper
  • 16.1 General
• 17. General assembly instructions
  • 17.1 Fitting gib-head keys
  • 17.2 Fitting tightening pins
  • 17.3 Fitting hydraulic pipes and screw connections
  • 17.4 Fitting a flanged bearing with locking collar
  • 17.5 Fitting sliding bushings
  • 17.6 Removing the revolution sensor
  • 17.7 Fitting tightening rings
• 18. Miscellaneous data
  • 18.1 General
  • 18.2 Speeds - adjustment values
  • 18.3 Maintenance