John Deere 8570, 8770, 8870 and 8970 tractor operator's manual (OMAR112116)

Table of Contents for JD-OMAR112116-EN manual

• Introduction
• Contents
• Safety
  • RECOGNIZE SAFETY INFORMATION
  • UNDERSTAND SIGNAL WORDS
  • FOLLOW SAFETY INSTRUCTIONS
  • STAY CLEAR OF MOVING TRACTOR
  • USE HAND HOLDS AND STEPS
  • PREVENT MACHINE RUNAWAY
  • USE SEAT BELT PROPERLY
  • OPERATING THE TRACTOR SAFELY
  • SHIFT TO LOW GEAR ON HILLS
  • USE CAUTION ON HILLSIDES
  • STOPPING AND PARKING TRACTOR
  • KEEP RIDERS OFF MACHINE
  • OPERATE RADAR UNIT SAFELY
  • HANDLE FUEL SAFELY-AVOID FIRES
  • PREPARE FOR EMERGENCIES
  • HANDLE STARTING FLUID SAFELY
  • WEAR PROTECTIVE CLOTHING
  • PROTECT AGAINST NOISE
  • HANDLE CHEMICAL PRODUCTS SAFELY
  • AVOID CONTACT WITH PESTICIDES
  • STAY CLEAR OF ROTATING DRIVELINES
  • USE SAFETY LIGHTS AND DEVICES
  • USE A SAFETY CHAIN
  • TRANSPORT TRACTOR SAFELY
  • TOW LOADS SAFELY
  • KEEP ROPS INSTALLED PROPERLY
  • PRACTICE SAFE MAINTENANCE
  • REMOVE PAINT BEFORE WELDING OR HEATING
  • AVOID HEATING NEAR PRESSURIZED FLUID LINES
  • AVOID HIGH-PRESSURE FLUIDS
  • PROTECT AGAINST HIGH PRESSURE SPRAY
  • SERVICE BRAKE ACCUMULATOR SAFELY
  • SERVICE COOLING SYSTEM SAFELY
  • STORE ATTACHMENTS SAFELY
  • DISPOSE OF WASTE PROPERLY
• Safety Signs
  • REPLACE DAMAGED OR MISSING SAFETY SIGNS
  • PREVENT MACHINE RUNAWAY
  • STAY CLEAR OF ENGINE FAN
  • OPERATE TRACTOR SAFELY
  • USE SEAT BELT
  • OPERATE FROM SEAT
  • STAY CLEAR OF PTO
  • PTO OVERSPEED
  • COUPLE IMPLEMENT SECURELY
  • AVOID HIGH-PRESSURE FLUID
  • AVOID ESCAPING FLUID
  • AVOID POSSIBLE EYE DAMAGE
• Controls and Instruments
  • SOUND-GARD
  • BODY ROOF CONTROLS
  • CONTROL CONSOLE
  • DECELERATOR CONTROL
  • SHIFT CONSOLE-12-SPEED SYNCRO AND 24-SPEED POWRSYNC
  • TRANSMISSION
  • SHIFT CONSOLE-12-SPEED POWER SHIFT TRANSMISSION
  • ELECTRONIC INSTRUMENTATION
  • INTELLITRAK
  • CHECK INSTRUMENTS OFTEN
  • OBEY "STOP ENGINE" SIGNAL
  • OBSERVE "SERVICE ALERT" SIGNAL
  • CHECK WARNING INDICATORS
  • CHECK WARNING INDICATORS- CONTINUED
  • IDENTIFYING TACHOMETER FUNCTIONS
  • WATCH FUEL LEVEL
  • CHECK ENGINE COOLANT TEMPERATURE GAUGE
  • TACHOMETER FUNCTION DESCRIPTION
  • IDENTIFYING PERFORMANCE MONITOR FUNCTIONS-OPTIONAL
  • PERFORMANCE MONITOR FUNCTION DESCRIPTION
  • AREA TOUCH SWITCH
  • PTO SPEED TOUCH SWITCH
  • ENGINE SPEED TOUCH SWITCH
  • DISTANCE TRAVELED TOUCH SWITCH
  • ADJUST TOUCH SWITCH
  • PERCENT SLIP TOUCH SWITCH
  • IMPLEMENT WIDTH TOUCH SWITCH
  • SERVICE HOURS TOUCH SWITCH
  • AREA/HOUR TOUCH SWITCH
  • RADAR SENSOR-OPTIONAL
  • PERFORMANCE MONITOR CALIBRATION WITH RADAR
• Lights
  • LIGHT SWITCH POSITIONS
  • USING HEAD LIGHTS
  • USING DIMMER SWITCH
  • USING TAIL LIGHTS
  • USING FIELD LIGHTS
  • ROOF-MOUNTED FIELD LIGHTS-OPTIONAL
  • USING HAZARD WARNING LIGHTS
  • USING ROAD TRANSPORT WARNING LIGHTS
  • TURN SIGNAL SWITCH
  • SEVEN-TERMINAL OUTLET
  • SEVEN-TERMINAL OUTLET CONNECTIONS
  • CONVENIENCE OUTLET
  • AUXILIARY EQUIPMENT MOUNTING BOSSES
  • ELECTRICAL JUNCTION BLOCK
  • ELECTRICAL CONNECTIONS FOR AUXILIARY EQUIPMENT
• Operator Station
  • AIR QUALITY SYSTEM (AQS) CONTROLS
  • SOUND-GARD
  • BODY (SGB) AIR FILTERS
  • CONTROLLING FRONT WINDSHIELD WIPER AND OPTIONAL REAR WINDSHIELD WIPER
  • OPENING WINDOW
  • OPERATING DEERE/DELCO AM-FM STEREO (SEEK/SCAN) RADIO WITH CLOCK AND CASSETTE-OPTIONAL
  • SETTING CLOCK
  • PRESETTING RADIO PUSH-BUTTONS
  • OPERATING TAPE PLAYER
  • USING SEAT BELT
  • PERSONAL POSTURE SEAT
  • ADJUSTING PERSONAL POSTURE SEAT
  • ADJUSTING ARMREST HEIGHT
  • ADJUSTING BACKREST ANGLE
  • ADJUSTING LUMBAR SUPPORT
  • USE OPERATOR'S MANUAL HOLDER
  • ADJUSTING STEERING WHEEL
• Engine Break-in
  • ENGINE BREAK-IN
  • ENGINE BREAK-IN-8570, 8770 AND 8870 TRACTORS
• Prestarting Checks
• Operating the Engine
  • START-UP PRECAUTIONS
  • STARTER SWITCH POSITIONS
  • ADJUSTING TRACTOR CONTROLS
  • CHECKING INSTRUMENT OPERATION
  • STARTING ENGINE
  • COLD WEATHER STARTING AIDS
  • COLD WEATHER STARTING PROCEDURE
  • CHANGING STARTING FLUID CANS
  • USING ELECTRIC COOLANT HEATER-OPTIONAL
  • USING A BOOSTER BATTERY OR BATTERY CHARGER
  • ENGINE WARM-UP
  • TRANSMISSION AND HYDRAULIC SYSTEM WARM-UP
  • CHANGING ENGINE SPEEDS
  • USING FIELD CRUISE AND FOOT DECELERATOR
  • ENGINE LOAD
  • PTO SPEED
  • IDLING ENGINE
  • RESTARTING STALLED ENGINE
  • STOPPING THE ENGINE
• Operating the Tractor
  • AVOID CONTACT WITH PESTICIDES
  • CLEAN TRACTOR OF HAZARDOUS PESTICIDES
  • USING BRAKES
  • USING DIFFERENTIAL LOCK-OPTIONAL
  • OPERATING 12-SPEED SYNCRO AND 24-SPEED POWRSYNC TRANSMISSION CONTROLS
  • SELECTING GEARS-SYNCRO AND POWRSYNC
  • SHIFTING TRANSMISSION-SYNCRO AND POWRSYNC
  • SHIFTING ON-THE-GO-12-SPEED SYNCRO
  • SHIFTING ON-THE-GO-24-SPEED POWRSYNC
  • OPERATING POWER SHIFT TRANSMISSION
  • SELECTING PROPER GEARS- POWER SHIFT
  • ENGAGING TRANSMISSION-POWER SHIFT
  • SHIFTING ON-THE-GO-POWER SHIFT
  • COME-HOME FEATURE-POWER SHIFT
  • OPERATIONAL STATUS CODES- POWER SHIFT
  • • STATUS CODE-FLASHING "N"
  • • STATUS CODE-"TA"
  • • STATUS CODE-"T" SERIES
  • • STATUS CODE-"S SERIES"
  • • STATUS CODE-"PP"
  • • STATUS CODE-"I" SERIES
• Hitch
  • MATCH TRACTOR POWER TO IMPLEMENT
  • LOCATING THREE-POINT HITCH COMPONENTS
  • USING HITCH CONTROL LEVER
  • LOAD/DEPTH MIX CONTROL
  • USING POSITION CONTROL
  • USING FLOAT POSITION
  • USING DRAFT CONTROL
  • SETTING UPPER HEIGHT LIMIT
  • ADJUSTING RATE-OF-DROP
  • USING EXTERNAL RAISE/LOWER SWITCH
  • HITCH CONTROL SYSTEM RESET
  • HITCH CONTROL SYSTEM TROUBLESHOOTING
  • USING SWAY BLOCKS
  • ATTACHING IMPLEMENT TO QUICK COUPLER
  • ADJUSTING IMPLEMENT LEVEL
  • LATERAL FLOAT
  • REMOVING IMPLEMENT
• Remote Hydraulic Cylinders
  • USING CORRECT HOSE TIPS
  • IDENTIFYING SCV NUMBER
  • CONNECTING CYLINDER HOSES
  • CONNECTING HOSE UNDER PRESSURE
  • ADJUSTING RATE-OF-CYLINDER AND HYDRAULIC MOTOR OPERATION
  • USING REMOTE CYLINDER LEVERS
  • 1. NEUTRAL LEVER POSITION
  • 2. EXTEND POSITION
  • 3. AUTOMATIC EXTEND POSITION
  • 4. RETRACT POSITION
  • 5. AUTOMATIC RETRACT POSITION
  • 6. FLOAT POSITION
  • ADJUSTING REMOTE CYLINDER STROKE
  • ADJUSTING CYLINDER HYDRAULIC STOP
  • ADJUSTING CYLINDER MECHANICAL STOP
  • DISCONNECTING CYLINDER HOSE
  • ADJUSTING SCV LINKAGE
• Drawbar and PTO
  • OBSERVING DRAWBAR LOAD LIMITATIONS
  • SELECTING DRAWBAR POSITION
  • ADJUSTING DRAWBAR SIDE-TO-SIDE
  • USING HAMMER STRAP ASSEMBLY
  • INSTALLING HAMMER STRAP ASSEMBLY
  • SWINGING DRAWBAR
  • USING PTO MASTER SHIELD
  • ATTACHING PTO DRIVEN IMPLEMENT
  • OPERATING PTO
• Optimum Performance/Ballast
  • PLANNING FOR MAXIMUM PRODUCTIVITY
  • SELECTING BALLAST CAREFULLY
  • MATCHING BALLAST TO WORK LOAD
  • ATTAINING OPTIMUM PERFORMANCE
  • USING RECOMMENDED WEIGHT SPLIT
  • CONTROLLING POWER HOP
  • BALLASTING FOR ENGINE HORSEPOWER
  • USING CAST HUB WHEEL WEIGHTS
  • USING LIQUID BALLAST IN TIRES
  • TIRE INFLATION PRESSURE GUIDELINES
  • RADIAL TIRE PRESSURES
  • BIAS-PLY TIRE PRESSURES
  • CHECKING FOR CORRECT BALLAST
  • MEASURING WHEEL SLIP-MANUALLY
  • USING BALLAST LIMITATIONS
• Wheels, Tires, and Treads
  • TIGHTEN WHEEL BOLTS CORRECTLY
  • USING RADIAL-PLY TIRES
  • DO NOT MIX TIRE SIZES
  • OBSERVING TREAD WIDTH LIMITATIONS
  • CHOOSING TREAD WIDTH
  • SINGLE OR DUAL TREAD WIDTHS
  • TRIPLE TREAD WIDTH
  • ADJUSTING TREAD WIDTH (STEEL)
  • ADJUSTING TREAD WIDTH (CAST)
  • USE STEERING STOPS
• Transporting
  • DRIVING TRACTOR ON ROADS
  • TRANSPORTING ON CARRIER
  • TOWING-REAR WHEELS OFF GROUND
  • TOWING-ALL WHEELS ON GROUND
  • 12-SPEED SYNCRO AND 24-SPEED POWERSYNC TRANSMISSION
• Fuels, Lubricants, and Coolant
  • DIESEL FUEL
  • FUEL STORAGE
  • FILL FUEL TANK
  • DIESEL ENGINE OIL-8570, 8770 AND 8870 TRACTORS
  • ENGINE BREAK-IN OIL-8570, 8770 AND 8870 TRACTORS-NEW ENGINES
  • OIL FILTERS
  • DIESEL ENGINE COOLANT
  • LIQUID COOLANT CONDITIONER
  • TRANSMISSION AND HYDRAULIC OIL
  • USE CORRECT HYDRAULIC-TRANSMISSION FILTER ELEMENT
  • GREASE
  • ALTERNATIVE AND SYNTHETIC LUBRICANTS
  • LUBRICANT STORAGE
  • MIXING OF LUBRICANTS
  • AND COOLSCAN™
  • OILSCAN
• Service
  • ADDITIONAL SERVICE INFORMATION
  • OBSERVE SERVICE INTERVALS
  • OBSERVING SERVICE INTERVALS-CUMMINS ENGINE
  • USING CORRECT LUBRICANT
  • ENGINE ACCESS
  • CLOSING HOOD
  • CLOSING HOOD EXTENSION
  • BATTERY COMPARTMENT ACCESS
  • COWL REMOVAL
  • INSTRUMENT MODULE ACCESS
  • USING HIGH-PRESSURE WASHERS
  • BREAK-IN PERIOD
  • SERVICE INTERVAL CHART *
• Service/Daily or Every 10 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • CHECK COOLANT LEVEL
  • CHECK ALL TIRES
  • CHECK ENGINE OIL LEVEL
  • DRAIN WATER SEPARATOR
  • CHECK TRANSMISSION OIL LEVEL
  • CHECK HYDRAULIC OIL LEVEL
  • LUBRICATE HINGE PINS
  • LUBRICATE AXLE BEARINGS
  • LUBRICATE LIFT CYLINDER PINS
  • REFER TO CUMMINS OPERATOR'S MANUAL FOR THE 8970 ENGINE
• Service/After 100 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • CHANGE ENGINE OIL
  • CHANGE ENGINE OIL FILTER ELEMENTS
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-12-SPEED SYNCRO AND 24-SPEED POWRSYNC TRANSMISSIONS
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-POWER SHIFT TRANSMISSION
  • CHANGE HYDRAULIC OIL FILTER ELEMENT
  • CHECK AND ADJUST BELT TENSIONS
  • CHECK COOLING SYSTEM HOSES
  • CHECK AIR INTAKE SYSTEM HOSES
  • CHECK FUEL INJECTION LINES
• Service/250 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • LUBRICATE GUDGEON SPINDLE BEARINGS
  • LUBRICATE TELESCOPING DRIVESHAFTS
  • LUBRICATE LOWER DRIVELINE BEARING
  • CLEAN SOUND-GARD BODY RECIRCULATED AIR FILTER
  • LUBRICATE THREE-POINT HITCH CENTER LINK AND LIFT LINKS
  • CHANGE ENGINE OIL AND FILTER
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-POWER SHIFT TRANSMISSION
  • SERVICE BATTERIES
  • CHECK BELT TENSIONS
  • ADJUSTING FAN AND ALTERNATOR BELT TENSION-8570, 8770 AND 8870 TRACTORS
  • ADJUSTING COMPRESSOR BELT TENSION-8570, 8770 AND 8870 TRACTORS
  • INSPECT TRACTOR FOR LOOSE BOLTS
  • KEEP ROPS INSTALLED PROPERLY
  • CHECK NEUTRAL START SYSTEM
  • CHECK BRAKE ACCUMULATOR
  • INSPECT FIRE EXTINGUISHER-IF EQUIPPED
  • LUBRICATE HITCH SENSOR
  • REFER TO CUMMINS OPERATOR'S MANUAL FOR THE 8970 ENGINE
• Service/500 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • LUBRICATE AXLE BEARINGS
  • COOLANT CONDITIONER-8570 TRACTOR
  • REPLACE FINAL FUEL FILTER ELEMENT-8570, 8770 AND 8870 TRACTORS
  • REPLACE PRIMARY FUEL FILTER-8570, 8770 AND 8870 TRACTORS
• Service/750 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-12-SPEED SYNCRO AND 24-SPEED POWRSYNC TRANSMISSIONS
  • CHANGE HYDRAULIC OIL FILTER ELEMENT
  • CHECK COOLING SYSTEM HOSES
  • REMOVE AND CLEAN CRANKCASE VENT TUBE
  • DRAIN FUEL TANK SUMP
  • CHECK AIR INTAKE SYSTEM HOSES AND CLAMPS
  • CLEAN AND INSPECT MAIN HYDRAULIC PUMP SCREEN
  • INSPECT HYDRAULIC RESERVOIR BREATHER
  • INSPECT FUEL TANK BREATHER
• Service/1000 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • ADJUST ENGINE VALVE CLEARANCE- 8770 AND 8870 TRACTORS
  • CHANGE TRANSMISSION OIL-POWER SHIFT TRANSMISSION
• Service/1500 Hours
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • CHANGE TRANSMISSION OIL-12-SPEED SYNCRO AND 24-SPEED POWRSYNC
  • CHANGE HYDRAULIC AND DIFFERENTIAL OIL
  • CLEAN FRONT AXLE SUCTION SCREEN
  • CHECK FUEL INJECTION NOZZLES
  • CLEAN TRANSMISSION SUMP SCREEN-12-SPEED SYNCRO AND 24-SPEED POWRSYNC
  • SERVICE COOLING SYSTEM
  • COOLING SYSTEM FLUSH
  • REPLACE COOLANT FILTER-8770, 8870 AND 8970 TRACTORS
  • WINTERIZING COOLING SYSTEM
  • REFER TO CUMMINS OPERATOR'S MANUAL FOR THE 8970 ENGINE
• Service/2000 Hours
  • ADJUST ENGINE VALVE CLEARANCE- 8570 TRACTORS
• Service/Annually
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • REPLACE PRIMARY AND SECONDARY AIR FILTERS
  • REMOVING AIR CLEANER ELEMENT
  • REPLACE AIR QUALITY SYSTEM (AQS) FILTER
  • LUBRICATE HITCH SENSOR
  • CHECK CUMMINS OR JOHN DEERE ENGINE MOUNTS
  • REFER TO CUMMINS OPERATOR'S MANUAL FOR THE 8970 ENGINE
• Service/2 Year
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • COOLING SYSTEM
  • REPLACE THERMOSTATS
• Service/As Required
  • OBSERVE SERVICE INTERVAL-CUMMINS ENGINE
  • REPLACE PRIMARY AND SECONDARY AIR FILTERS
  • CLEAN AND INSPECT PRIMARY ELEMENT
  • CLEAN AIR QUALITY SYSTEM AIR FILTER
  • CLEAN AIR QUALITY SYSTEM EVAPORATOR/HEATER CORE
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-12-SPEED SYNCRO AND 24-SPEED POWRSYNC TRANSMISSIONS
  • CHANGE TRANSMISSION OIL FILTER ELEMENT-POWER SHIFT TRANSMISSION
  • REPLACE HYDRAULIC FILTER ELEMENT
  • CLEAN HYDRAULIC OIL FILTER CHARGE MAKEUP SCREEN
  • CHECK ENGINE OIL FILLER CAP-8770 AND 8870 TRACTORS
  • REPLACE PRIMARY FUEL FILTER-8570, 8770 AND 8870 TRACTORS
  • REPLACE FINAL FUEL FILTER-8570, 8770 AND 8870 TRACTORS
  • BLEEDING THE FUEL SYSTEM-8570, 8770 AND 8870 TRACTORS
  • BLEEDING FUEL SYSTEM-8970 TRACTOR
  • DRAIN FUEL TANK SUMP
  • BLEED BRAKES
  • CLEAN HYDRAULIC RESERVOIR SUMP SCREEN
  • CLEAN EXHAUST STACK AND MUFFLER AREA
  • CLEAN ENGINE COMPARTMENT
  • CLEANING GRILLE SCREENS, RADIATOR AND OIL COOLER
  • INSPECT ENGINE CRANKSHAFT DAMPER
  • INSPECT TRANSMISSION DRIVE SHAFT DAMPER
  • ADJUST PARK BRAKE
  • REPLACING FAN AND ALTERNATOR BELTS-8570, 8770 AND 8870 TRACTORS
  • REPLACING COMPRESSOR BELT-8570, 8770 AND 8870 TRACTORS
  • REPLACING BELTS-8970 TRACTOR
  • OBSERVE ELECTRICAL SERVICE PRECAUTIONS
  • BATTERY REPLACEMENT
  • CONNECTING BATTERY CABLES
  • CHECKING ELECTRICAL LOAD CENTER
  • FUSE/RELAY LOCATION
  • SERVICING LIGHT BULBS
  • REPLACING HEAD OR FLOOD LIGHTS
  • REPLACING TAIL OR WARNING LIGHT BULB
  • REPLACING ROAD TRANSPORT WARNING LIGHT BULB
  • REPLACING DOME AND CONSOLE BULBS
  • REPLACING WARNING INDICATOR LIGHTS
  • REPLACING DIGITAL TACHOMETER OR PERFORMANCE MONITOR BACK-LIGHT BULBS
  • BULB REPLACEMENT CHART
  • ADJUST HEAD LIGHTS
  • CONNECTING STARTER WIRING
  • CONNECTING ALTERNATOR WIRING
  • SERVICING AIR CONDITIONER
  • CHECKING HYDRAULIC HOSES
  • REFER TO CUMMINS OPERATOR'S MANUAL FOR THE 8970 ENGINE
• Troubleshooting
  • ENGINE
  • TRANSMISSION
  • DRIVE LINE
  • HYDRAULIC SYSTEM
  • BRAKES
  • AXLES
  • THREE-POINT HITCH AND QUICK-COUPLER
  • REMOTE HYDRAULIC CYLINDERS
  • ELECTRICAL SYSTEM
  • SOUND-GARD BODY
  • TRACTOR OPERATION TROUBLESHOOTING
• Storage
  • PLACE TRACTOR IN STORAGE
  • REMOVE TRACTOR FROM STORAGE
• Crime Prevention Tips
  • HELP PREVENT CRIME
  • RECORD IDENTIFICATION NUMBERS
  • KEEP PROOF OF OWNERSHIP
  • PARK INDOORS OUT OF SIGHT
  • WHEN PARKING OUTDOORS
  • REDUCE VANDALISM
  • REPORT THEFTS IMMEDIATELY
• Specifications
  • GENERAL SPECIFICATIONS
  • GROUND SPEEDS-12-SPEED SYNCRO AND 24-SPEED POWRSYNC
  • GROUND SPEEDS-12-SPEED POWER SHIFT
  • GROUND SPEED CONVERSION FACTORS
  • UNIFIED INCH BOLT AND CAP SCREW TORQUE VALUES
  • METRIC BOLT AND CAP SCREW TORQUE VALUES
  • LIMITED BATTERY WARRANTY
• Identification Numbers
  • IDENTIFICATION PLATES
  • RECORD TRACTOR IDENTIFICATION NUMBER
  • RECORD ENGINE SERIAL NUMBER-8570 TRACTOR
  • RECORD ENGINE SERIAL NUMBER-8770 AND 8870 TRACTOR
  • RECORD ENGINE SERIAL NUMBER-8970 TRACTOR
  • RECORD SOUND-GARD BODY SERIAL NUMBER
  • RECORD TRANSMISSION SERIAL NUMBER
  • RECORD HYDRAULIC PUMP SERIAL NUMBER
  • RECORD BOTH AXLE SERIAL NUMBERS
  • RECORD PTO SERIAL NUMBERS
• Daily Maintenance
  • DAILY OR EVERY 10 HOURS SERVICES
• Lubrication and Maintenance Records
  • 250 HOUR SERVICE (REFER TO SERVICE SECTION)
  • 500 HOUR SERVICE (REFER TO SERVICE SECTION)
  • 750 HOUR SERVICE (REFER TO SERVICE SECTION)
  • 1000 HOUR SERVICE (REFER TO SERVICE SECTION)
  • 1500 HOUR SERVICE (REFER TO SERVICE SECTION)
  • 2000 HOUR SERVICE (REFER TO SERVICE SECTION)
  • ANNUAL SERVICE (REFER TO SERVICE SECTION)
  • SERVICE EVERY TWO YEARS (REFER TO SERVICE SECTION)
• Index
  • A
  • D
  • B
  • E
  • C
  • H
  • F
  • I
  • G
  • L
  • M
  • S
  • N
  • O
  • T
  • P
  • Q
  • R
  • W
• John Deere Service Literature Available
  • PARTS CATALOG
  • OPERATOR'S MANUAL
  • TECHNICAL AND SERVICE MANUALS
  • JOHN DEERE PUBLISHING BOOKS
  • CUMMINS SERVICE LITERATURE
• John Deere Service Keeps You On The Job
  • JOHN DEERE IS AT YOUR SERVICE WHEN YOU NEED IT